01759 368588


 My Cart

Items:  items
Value: 

View CartCheckout

 My Cart

Items:  items |  Value: 
View Cart | Checkout

Stewart Oster

Page:  1  2  3  4   >   >>   View All (45)

Mk III diagram
Mk I diagram
Mk II diagram

Head information

Head information


FIGURE 1: Internal head section
Clipmaster head with blades removed .

A Yoke assembly with two pointed "cones" on which the cutter blade is seated.
B Drive block. This should be seated within the yoke assembly to work.
C Oscillating springs - consisting of three "leaves" each side of the yoke assembly.
D Rubber band - secures yoke assembly over the drive block when blades not fitted.
E Lower blade screws. Used a "wide" blade type screwdriver to undo/tighten.
F Screws for securing yoke assembly.


FIGURE 2: Protecting the drive block against loss

Once the cutter and comb blades have been removed from the clipper head, the yoke assembley will drop down when the clipper is held in the normal upright position. As a result the drive block can easily be lost, often without the user realising! Should this occur, the clipper blades will not work.

UNDER NO CIRCUMSTANCES should the machine be switched on - as use without a drive block may result in serious damages to the head and or the body mechanism.

A replacement drive block MUST be fitted before the machine can be used again.

In order to prevent the yoke assembly dropping down and accidental loss of the drive block, a simple remedy is to secure the yoke assembly over the drive block with a rubber band until such time as you refit the blades.



FIGURE 3: Over tensioning blades

Over tensioning of the blades should be avoided as this can lead to the "pressure plate" located inside the tension plate assembly) either breaking or being damages - in which case you will not be able to tension the blades. In this event the whole tension plate assembly (104460-005-000) has to be replaced as the pressure plate is an integeral part. (The tension nut on the top of the clipper head - See item 18 on the parts diagram - head above

Over tensioning or running the machine without blades can also lead to the stripping of the gear wheel cog teeth (044910-000-000) To check or replace the crankshaft gear you need to detach the clipper head from the body, unscrew and removed the cover plate - (See item 2 on the parts diagram - head.)


NB. This information applies to all three models of the Stewart Oster Clipmaster as well as certain AESCULAP, HEINIGER and LISCOP/LIVERYMAN horse/cattle clippers which have the same or similar head mechanism. Therefore the same comments may be considered to apply.



Customer information


IMPORTANT - CUSTOMERS INFORMATION
This page is under constant construction with new parts being added. Please also note any manufacturer’s updates as listed

Always scroll FULLY down the page to see both updates and current parts listed

Some pages may only show a limited number of parts – you will need to CLICK View All (See the top of the page above the diagram or at the bottom of each page)

If you require further advice please contact us.

E-mail:
shop@peasridge.co.uk

Telephone:
UK Mainland: 01424 882900/882211
Overseas: 0044 1424 882900/882211

PLEASE NOTE
Telephone lines are open from (UK time: ) 1030 to 1230 hours and from 1430 until 1630 hours Monday to Friday. Our offices are shut on Saturday, Sunday and all Bank Holidays.

Product items such as ADAPTERS, BATTERIES & CHARGER UNITS are listed under CLIPPER ACCESSORIES
See STORE SELECTIONS on the LHS of your screen

ORDERING PARTS
Please have details relating to make and model of machine, as well as applicable part or diagram identification numbers to hand. Failure to do this may result in errors in the parts ordered/supplied.

TRADE DISCOUNTS
Trade discounted prices are available on all parts to bona fide trade repair businesses. Please contact us for further information

SHIPPING
We make every effort to ship parts the same day for next day delivery on the UK Mainland

INTERNATIONAL SHIPPING
We ship worldwide daily.


MANUFACTURER'S UPDATES
We understand that a number of STEWART OSTER CLIPMASTER parts are being upgraded. These require to be inspected and passed by International Regulators to obtain the necessary EU and other European electrical certification which is required before they can be sold in Europe.

It is expected that these parts will become available again in 2016.

PLEASE WATCH FUTURE UPDATES

Head attachment

Head attachment

Price: 155.33 (Including VAT at 20%)

Ref: C0025

Lower casing

Lower casing

Price: 43.32 (Including VAT at 20%)

Ref: 105695-015-000

Upper casing

Upper casing

Price: 48.86 (Including VAT at 20%)

Ref: 105694-015-000

 

Body screw - front

Body screw - front

Price: 0.17 (Including VAT at 20%)

Ref: 044999-005-000

Body screw - rear

Body screw - rear

Price: 1.39 (Including VAT at 20%)

Ref: 042109-000-000

Lower blade screw

Lower blade screw

Price: 0.64 (Including VAT at 20%)

Ref: 55717-000-000

Air filter

Air filter

Price: 0.46 (Including VAT at 20%)

Ref: 045538-000-000

Air filter screw

Air filter screw

Price: 0.14 (Including VAT at 20%)

Ref: 042109-010-000

On/Off  switch

On/Off switch

Price: 9.29 (Including VAT at 20%)

Ref: 058513-010-000

Armature assembly

Armature assembly

Price: 125.40 (Including VAT at 20%)

Ref: 107100-001-000

O-ring seal - front

O-ring seal - front

Price: 0.62 (Including VAT at 20%)

Ref: 045591-000-000

O-ring

O-ring

Price: 0.60 (Including VAT at 20%)

Ref: 042891-000-000

Page:  1  2  3  4   >   >>   View All (45)



Menu


Click anywhere outside this panel to close it.

Right panel

Clicking outside this panel wont close it because clickClose = false