Advanced
Online Catalogue
>
CLIPPER PARTS
>
Oster clipper parts
>
OSTER A5 Single speed parts
OSTER A5 Single speed clipper - Blade latch
Product code: 72527
OSTER A5 Single speed clipper - Blade latch release lever
Part number: 72527
See clipper diagram above for parts location.
PLEASE NOTE:
Ensure the two hair thin metal spring sprigs protruding from the hinge assembly (see red arrows) are both correctly seated in the small pin sized holes on the right and left hand sides of the latch assembly as these are essential to the latch release control working correctly.
The latch release assembly is located and fixed behind the hinge assembly.
Position and keep both in place before re-screwing both the latch and hinge to the clipper head.
Price: £1.29
(Including: VAT at 17.5%)
OSTER A5 Single speed clipper - Blade hinge assembly
Product code: 72576
OSTER A5 Single speed clipper - Blade hinge assembly
Part number: 72576
See clipper diagram above for parts location.
PLEASE NOTE:
Ensure the two hair thin metal spring sprigs protruding from the hinge assembly (see red arrows) are both correctly seated in the small pin sized holes on the right and left hand sides of the latch assembly as these are essential to the latch release control working correctly.
The latch release assembly is located and fixed behind the hinge assembly.
Position and keep both in place before re-screwing both the latch and hinge to the clipper head.
Price: £7.11
(Including: VAT at 17.5%)
OSTER A5 Single speed clipper - Blade drive lever
Product code: 72763
OSTER A5 Single speed clipper - Blade drive lever
Part number: 72763
See clipper diagram above for parts location.
PLEASE NOTE:
Un-screw and remove the makers name plate on the head of the clipper to locate the blade drive lever. Assembly can be seen from the diagram above.
Please note the warnings about excess greasing gven on the parts diagram!
This area needs routinely checking monthly for the average working machine.
Re grease if found dry or limited.
Price: £1.55
(Including: VAT at 17.5%)
OSTER A5 Single speed clipper - Gearwheel
Product code: 72099
OSTER A5 Single speed clipper - Gearwheel assembly - 21 teeth
Part number: 72099
See clipper diagram above for parts location.
IMPORTANT - Please Note!
Customers are reminded to take note of the greasing instruction as set out in the clipper diagram above.
IMPORTANT - Please Note!
Persons considering making repairs to clippers themselves should be mindful such repairs may invalidate the warranty especially where it specifies repairs are to be carried out by an authorised service establishment or qualified engineer. Please refer to your clipper manual.
In addition repairs of an electrical nature or situations involving the main body casing being opened, legally require a "mandatory" electrical test to be undertaken at an approved repair centre before the machine is used again.
Price: £15.25
(Including: VAT at 17.5%)
OSTER A5 Single speed clipper - carbon brush and spring assembly
Product code: 62106
OSTER A5 Single speed clipper - carbon brush and spring set (2)
Part number: 62106
Suitable for the Oster A5 single speed model: Set of two carbon brushes with springs
See clipper diagram above for parts location.
Carbon brushes should be replaced as a pair and NOT singularly.
Un-screw brush cap to remove brushes.
To check for wear and replacement, remove brushes and compare the length of the round and square sections of each brush. If the square section has worn to the length of the round section, the brushes need to be replaced to avoid potential damage to the motor and armature with associated costly replacement.
See your clipper manual for full instructions for removal and re-fitting
PLEASE NOTE:
When un-screwing the carbon brush housing caps, the existing carbon brush and spring may "fly" out!
When replacing please note the carbon brush is insert first - the spring next!
Price: £4.78
(Including: VAT at 17.5%)
Online Catalogue
>
CLIPPER PARTS
>
Oster clipper parts
>
OSTER A5 Single speed parts
