| |
|
 | Hauptner 2000 - Body screws
Product code: 89500.610
Hauptner 2000 Set of crew (2) for head to body fixing complete with locking washers (2)
Part number: 89500.610
See diagram above.
Price: £3.53 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Reset switch
Product code: 89200.880
Hauptner 2000 - Reset switch - also referred to as the overload or overcharge switch
Part number: 89200.880
See diagram above.
IMPORTANT - Please Note!
Persons considering making repairs to clippers themselves should be mindful such repairs may invalidate the warranty especially where it specifies repairs are to be carried out by an authorised service establishment or qualified engineer. Please refer to your clipper manual.
In addition repairs of an electrical nature or situations involving the main body casing being opened, legally require a "mandatory" electrical test to be undertaken at an approved repair centre before the machine is used again.
Price: £20.12 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Toothed gear wheel
Product code: 89500.080
Hauptner 2000 Toothed gear wheel without shaft
Part number: 89500.080
See diagram above.
Price: £14.34 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Air filter
Product code: 89100.960
Hauptner 2000 Air filter housing
Part number: 89100.960
See diagram below.
Price: £6.72 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Screw for air filter
Product code: 89100.970
Hauptner 2000 - Screw for fixing the air filter (1 only)
Part number: 89100.970
See diagram above.
Price: £2.66 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Eccenter shaft
Product code: 89500.060
Hauptner 2000 Eccenter shaft without gear cog,
Part number: 89500.060
Price: £22.63 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Carbon brush with spring
Product code: 89500.430
Hauptner 2000 carbon brush and spring set (two items)
Part number: 89500.430
Replacement carbon brush and spring set for the Hauptner model: 2000 carbon brush and spring set for the Hauptner 2000 clipper
Carbon brushes need to be checked every 300/400 working hours for wear.
Brushes need to be checked by an authorised engineer at an approved service centre especially as special tools are needed to open the clipper body casing.
Worn carbon brushes can damage the motor and armature!
IMPORTANT - Please Note!
Persons considering making repairs to clippers themselves should be mindful such repairs may invalidate the warranty especially where it specifies repairs are to be carried out by an authorised service establishment or qualified engineer. Please refer to your clipper manual.
In addition repairs of an electrical nature or situations involving the main body casing being opened, legally require a "mandatory" electrical test to be undertaken at an approved repair centre before the machine is used again.
Price: £9.26 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Blade tension nut.
Product code: 86831.050
Hauptner 2000 blade tension nut.
Part number: 86831.050
See clipper diagram above for parts location.
Price: £6.76 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Blade tension bolt.
Product code: 86831.040
Hauptner 2000 blade tension bolt
Part number: 86831.040
See clipper diagram above for parts location.
Price: £5.95 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Blade tension spring.
Product code: 86831.030
Hauptner 2000 blade tension spring.
Part number: 86831.030
See clipper diagram above for parts location.
Price: £4.18 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Upper blade guides
Product code: 86831.020
Hauptner 2000 upper blade guides - set of two
Part number: 86831.020
See clipper diagram above for parts location.
Price: £4.79 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Blade drive bush
Product code: 89500.110
Hauptner 2000 blade drive bush
Part number: 89500.110
See clipper diagram above for parts location.
Price: £3.71 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Blade holding lugs
Product code: 89100.030
Hauptner 2000 blade holding lugs - set of 2
Part number: 89100.030
See clipper diagram above for parts location.
Price: £4.70 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Armature assembly
Product code: 89100.710
Hauptner Armature assembly complete with fan unit attached
Part number: 89100.710
IMPORTANT - Please Note!
Persons considering making repairs to clippers themselves should be mindful such repairs may invalidate the warranty especially where it specifies repairs are to be carried out by an authorised service establishment or qualified engineer. Please refer to your clipper manual.
In addition repairs of an electrical nature or situations involving the main body casing being opened, legally require a "mandatory" electrical test to be undertaken at an approved repair centre before the machine is used again.
IMPORTANT ELECTRICAL INFORMATION:
All electrical parts offered for sale are for use with the 220/240volt electrical supply system as operated in the UK and certain parts of Europe unless otherwise stated.
Customers from the USA and countries out side of the UK and European Countries should check their electrical supply rating and seek professional advice from a qualified electrician, before placing an order.
IF YOU FEEL YOU NEED TO DISCUSS YOUR CLIPPER REQUIREMENTS OR WANT FURTHER ADVICE
please contact us on Tel: 01424 882900
Price: £148.64 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Circuit board assembly - 30/50-watts
Product code: 89500.440
Hauptner 2000 - Circuit board assembly
Part number: 89500.440
This circuit board assembly should be used only on early produced Hauptner 2000 models with motors, which are marked "30-watts" or "50-watts"on the identification plate found at the rear of the clipper hand piece beneath the air filter. (See diagram)
They are not suitable for machines, which are stated as 180 watts or those with the prefix "C" at the start of the serial number.
IMPORTANT - Please Note!
Persons considering making repairs to clippers themselves should be mindful such repairs may invalidate the warranty especially where it specifies repairs are to be carried out by an authorised service establishment or qualified engineer. Please refer to your clipper manual.
In addition repairs of an electrical nature or situations involving the main body casing being opened, legally require a "mandatory" electrical test to be undertaken at an approved repair centre before the machine is used again.
IMPORTANT ELECTRICAL INFORMATION:
All electrical parts offered for sale are for use with the 220/240volt electrical supply system as operated in the UK and certain parts of Europe unless otherwise stated.
Customers from the USA and countries out side of the UK and European Countries should check their electrical supply rating and seek professional advice from a qualified electrician, before placing an order.
IF YOU FEEL YOU NEED TO DISCUSS YOUR CLIPPER REQUIREMENTS OR WANT FURTHER ADVICE
please contact us on Tel: 01424 882900
Price: £62.32 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Circuit board assembly - 180-watts
Product code: 89500.560
Hauptner 2000 - Circuit board assembly
Part number: 89500.560
This circuit board assembly should be used only on Hauptner 2000 models fitted with 180watt motors as stated on the identification plate found at the rear of the clipper hand piece beneath the air filter. (See diagram)
These circuit boards are interchangeable with the both 180watt machine and the latest models with the prefix "C" at the start of the serial number (part number 89500.510)
They are not suitable for use in the early Hauptner 30 watt machines, which need the part number 89500.440.
IMPORTANT - Please Note!
Persons considering making repairs to clippers themselves should be mindful such repairs may invalidate the warranty especially where it specifies repairs are to be carried out by an authorised service establishment or qualified engineer. Please refer to your clipper manual.
In addition repairs of an electrical nature or situations involving the main body casing being opened, legally require a "mandatory" electrical test to be undertaken at an approved repair centre before the machine is used again.
IMPORTANT ELECTRICAL INFORMATION:
All electrical parts offered for sale are for use with the 220/240volt electrical supply system as operated in the UK and certain parts of Europe unless otherwise stated.
Customers from the USA and countries out side of the UK and European Countries should check their electrical supply rating and seek professional advice from a qualified electrician, before placing an order.
Price: £62.32 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Circuit board assembly - Serial no prefix "C"
Product code: 89500.510
Hauptner 2000 - Circuit board assembly
Part number: 89500.510
This circuit board assembly should be used only on Hauptner 2000 models with motors, which are registered with the prefix "C" at the start of the serial number as marked on the identification plate found at the rear of the clipper hand piece beneath the air filter. (See diagram)
These circuit boards are also interchangeable with the earlier 180-watt models of the Hauptner 2000.
IMPORTANT - Please Note!
Persons considering making repairs to clippers themselves should be mindful such repairs may invalidate the warranty especially where it specifies repairs are to be carried out by an authorised service establishment or qualified engineer. Please refer to your clipper manual.
In addition repairs of an electrical nature or situations involving the main body casing being opened, legally require a "mandatory" electrical test to be undertaken at an approved repair centre before the machine is used again.
IMPORTANT ELECTRICAL INFORMATION:
All electrical parts offered for sale are for use with the 220/240volt electrical supply system as operated in the UK and certain parts of Europe unless otherwise stated.
Customers from the USA and countries out side of the UK and European Countries should check their electrical supply rating and seek professional advice from a qualified electrician, before placing an order.
Price: £68.39 (Including: VAT at 17.5%)
|
|
|
 | Hauptner 2000 - Control lever switch
Product code: 89500.670
Hauptner 2000 - Control lever switch
Part number: 89500.670
On/off attached control lever switch - new design replacing existing switch mechanisums.
Please note: This does not include the actual switch, it is the switch internal mechanism only.
IMPORTANT - Please Note!
Persons considering making repairs to clippers themselves should be mindful such repairs may invalidate the warranty especially where it specifies repairs are to be carried out by an authorised service establishment or qualified engineer. Please refer to your clipper manual.
In addition repairs of an electrical nature or situations involving the main body casing being opened, legally require a "mandatory" electrical test to be undertaken at an approved repair centre before the machine is used again.
Price: £4.72 (Including: VAT at 17.5%)
|
|
